Description of LCD display screen
TST28011T-00 is 2.8 inch lcd display screen with 37 pins MCU 8/16 bits interface, FPC is with soldering connection, except for this model, we also have other lcd display screen which is with ZIF connection. Driver IC is Sitronix ST7789V, available to add the standard capacitive touch screen or make the customized of all kinds of touch panels basing on your detail requirements.Standard brightness is 320 cd/m2, widely using in smart home, white goods, industrial and medical applications.
Team source display have ISO13485 and IAFT16949 certification, any needs of lcd display screen, we're happy to help and support.
Specification of LCD display screen
| LCD type | lcd display screen |
| Part No. | TST28011T-00 |
| Resolution | 240xRGBx320 |
| Outline dimension | 50x69.2x2.25mm |
| Active Area | 43.2x57.6mm |
| Brightness | 320 cd/m2 |
| Interface | MCU 8/16 bits |
| Viewing angle | 12 o'clock |
| Operating temperature | -20℃ to +70℃ |
| Storage temperature | -30℃ to +80℃ |
240X320 resolution, TN display and IPS display for your chosen
Support MCU 8 bits and16-bit color display, display rich colors
Standard and customized touch screen is available to make
Compatible with 3.3V operating voltage
Samples are available to send to test
Industrial-grade process standards, long-term stable work
Provide driver technical support
|
Office Electronic Equipment: money counting machine, office phone set, copying mechine |
|
Household Appliances: refrigerator, air conditioner, induction cooker, microwave ovens |
|
Instruments: clinical thermometer, wire tester, digital watches, electronic weight scale |
|
Medical Devices: sphygmomanometer |
|
Sports Equipment: running machine |
|
Industrial Control Equipment: remote control, punched-card machine |
|
Sports Equipment: running machine |
|
Handheld Terminal Display: POS, PDA |
|
Security Products: elevator controller, electronic indicator, video door system |
|
Smart home and white goods, cooling and heating system, thermostat, controller |
TEAM SOURCE DISPLAY is available to provide full ranges of LCD display from 0.96 inch to 21.5 inch, as well as this lcd display screen, also have the ability to provide all kinds of standard capacitive touch panel and make the customization of various capacitive touch panel basing on customers' requirement.
Q: What's the process to make the soldering of FPC?
1. Take 1 pieces of product to be welded and lay it flat on the table.
The welding place between the FPC and the backlight pad should be placed on a high temperature pad, not directly on the desktop.
2. FPC pad with bottom tin
Hold the soldering iron tip with the right hand and place it at about 45 degrees to the FPC surface and place it at the FPC pad. Use the tin wire in the left hand to tin the tip of the soldering iron, and move the soldering iron tip with the right hand to tin the FPC pad, and pay attention to below points:
A. The tinning time should not exceed 2-3 seconds to prevent scalding FPC (bubble)
B. Before tinning the tip of the soldering iron, wipe the dirt and excess tin slag on the wet foam.
3. Alignment welding
After the FPC pad is tinned, the left hand aligns the backlight gold finger with the FPC pad up and down, and then uses a soldering iron to solder the solder joint. The specific quality control requirements are as follows:
A. The left hand of the soldered weighing scale is used to hold the PI position of the root of the FPC gold finger with a tin wire. After the soldering iron is removed, the tin wire is removed after the tin is cured to prevent the pad from lifting.
B. When soldering, place the soldering iron on the soldering position for 2~3 seconds to connect the tin on the upper and lower pads together.
C. Do not add too much tin during soldering to avoid tin remaining in the soldering position.
Q: Do you accept sample order or small quantity order?
A: Yes, you can place sample orders for testing first, and small quantity order as pilot production.
Q: What are the payment terms?
A: We usually accept T/T, Paypal, other terms to be negotiated.
Q: What’s the lead time?
A: Usually 3~5 days for sample orders if goods are in stock, and 4~5 weeks for mass production (basing on the quantity and product)
